ZBA38Y-16/25/40 C Dual Spring Safety Valve
Dual Spring Safety Valve for steam and air systems needing a dual spring safety valve assembly with A48Y valve pairs. Key selection data include DN50-DN150 Y-connector nominal size; paired A48Y size per catalog table, PN16, PN25 and PN40, Up to 350 deg C, materials, connection standard and set pressure.
Final set pressure, certified relieving capacity, material code and connection standard must be confirmed on the approved datasheet before purchase.
- Size range: DN50-DN150 Y-connector nominal size; paired A48Y size per catalog table
- Pressure rating: PN16, PN25 and PN40
- Temperature: Up to 350 deg C
- Connection: Flanged Y-type dual valve assembly
- Media: Steam and air
- Drawings, test records and material documents confirmed for the ordered configuration.
Technical Specifications and Selection Data
Product Model
ZBA38Y-16/25/40 C
Size Range
DN50-DN150 Y-connector nominal size; paired A48Y size per catalog table
Pressure Rating
PN16, PN25 and PN40
Temperature Range
Up to 350 deg C
Applicable Media
Steam and air
Connection Type
Flanged Y-type dual valve assembly
Standards and Compliance
GB/T 12241, GB/T 12242 and GB/T 12243 for safety valve design, performance and test references; model coding follows the JB/T 308 valve model method where applicable.
Engineering Insight: Model Logic and Application Boundary
Model code: A38 = dual full-lift spring safety valve assembly. The nominal DN refers to the Y-connector inlet; paired valve size follows the combination table.
Typical application: steam and air systems needing a dual spring safety valve assembly with A48Y valve pairs
Capacity review: Discharge and dimensions depend on the selected Y-connector and paired A48Y valve combination.
This product family should not be selected from model code, nominal size or pressure class alone. Confirm the relieving scenario, required capacity, set pressure, operating margin, temperature, back pressure and actual connection standard.
Dimensions and Selection Guide
The table below is transcribed from catalog page 24. Verify critical dimensions against the approved order drawing before fabrication or piping release.
| Ype) | Nominal Diameter (DN) | do | R | G | Nominal Diameter (DN) | do | Approx. H |
|---|---|---|---|---|---|---|---|
| A38Y-16/25/40C | 50 | 198 | 225 | 165 | 40 | 2×20 | 310 |
| A38Y-16/25/40C | 80 | 230 | 285 | 190 | 65 | 2×32 | 335 |
| A38Y-16/25/40C | 100 | 275 | 350 | 230 | 80 | 2×40 | 420 |
| A38Y-16/25/40C | 150 | 343 | 400 | 275 | 125 | 2×65 | 555 |
| A38Y A38Y Type Relevant A48Y | Nominal | ( DN) Diameter | ter | 50 | 80 | 100 | 150 |
| A38Y A38Y Type Relevant A48Y | A48Y Type | ( DN Nominal | ) Diameter | 32 | 50 | 65 | 100 |
RFQ checklist
RFQ checklist: model or valve type, DN/NPS, PN/Class, set pressure, relieving medium, operating temperature, body and trim material, inlet/outlet connection standard, cap/lever/pilot options, quantity, drawing, certificate and inspection requirements.
Failure Analysis, Manufacturing Evidence and Quality Control
Common misapplication risks: incorrect thread or connection standard, insufficient certified relieving capacity, unsuitable body or trim material, operating pressure too close to set pressure, unreviewed back pressure, and installation loads transferred to the valve.
Material review: body materials: Y-connector material WCB; other valve materials follow A48Y spring safety valve configuration. Trim and internals: Same main trim family as A48Y, with hard alloy sealing surface options according to order. Spring and stem: 50CrVA spring for standard service; stainless or coated fluoroplastic/304 spring options for corrosive service where specified.
Testing and inspection: Set pressure calibration, shell strength test, seat tightness/leakage test, reseating/blowdown check, dimensional inspection and material verification can be supplied according to the confirmed standard and order requirements.
Source and scope: product data is based on Zobai Safety Valve Product Catalog.pdf, catalog page 24. Project compliance remains subject to the approved datasheet, drawing, calculation and controlled certificates for the ordered configuration.
Review material traceability, type-test scope and project certificate requirements.
Related Products
FAQ
Safety Valve FAQs
What size, pressure and temperature data should be confirmed?
Size: DN50-DN150 Y-connector nominal size; paired A48Y size per catalog table. Pressure: PN16, PN25 and PN40. Temperature: Up to 350 deg C. Confirm the exact combination for the selected model.
Which media can this product family handle?
Steam and air. Material and sealing compatibility require review for the actual fluid composition and temperature.
Can the catalog dimension table be used for final fabrication?
Use it for preliminary review only. Confirm critical dimensions, connection details and orientation on the approved order drawing before piping or equipment fabrication.
What should be included in the RFQ?
RFQ checklist: model or valve type, DN/NPS, PN/Class, set pressure, relieving medium, operating temperature, body and trim material, inlet/outlet connection standard, cap/lever/pilot options, quantity, drawing, certificate and inspection requirements.