ZBA41Y-160/320 C/P/R Spring Low Lift Enclosed High Pressure Safety Valve

Spring Low Lift Enclosed High Pressure Safety Valve for high-pressure gas or liquid equipment and pipelines requiring compact low-lift overpressure protection. Key selection data include DN20-DN50, PN160 and PN320, Up to 200 deg C, materials, connection standard and set pressure.

Final set pressure, certified relieving capacity, material code and connection standard must be confirmed on the approved datasheet before purchase.

Technical Specifications and Selection Data

Product Model

ZBA41Y-160/320 C/P/R

Size Range

DN20-DN50

Pressure Rating

PN160 and PN320

Temperature Range

Up to 200 deg C

Applicable Media

Air, N2-H2 mixed gas, water, corrosive gases and corrosive liquids depending on material

Connection Type

High-pressure flanged inlet and outlet

Standards and Compliance

GB/T 12241, GB/T 12242 and GB/T 12243 for safety valve design, performance and test references; model coding follows the JB/T 308 valve model method where applicable.

Engineering Insight: Model Logic and Application Boundary

Model code: A41Y = flanged low-lift enclosed safety valve with hard alloy sealing surface; 160/320 identify high PN rating; C/P/R identify body material code.

Typical application: high-pressure gas or liquid equipment and pipelines requiring compact low-lift overpressure protection

Capacity review: Main connection dimensions are listed on the source catalog page. Discharge capacity and orifice sizing should be confirmed by set pressure, medium, temperature and applicable code.

This product family should not be selected from model code, nominal size or pressure class alone. Confirm the relieving scenario, required capacity, set pressure, operating margin, temperature, back pressure and actual connection standard.

Dimensions and Selection Guide

The table below is transcribed from catalog page 26. Verify critical dimensions against the approved order drawing before fabrication or piping release.

Catalog page 026 – Parameter Table 1
Type / Model	Nominal Diameter (DN)	do	Column 4	Column 5	Column 6	Column 7	Z-Qd	Column 9	dl	Column 11	MI	Column 13	KI	Z1	bl	Column 17	Column 18	Column 19
A41Y-160			20	M24x2	95	60	3.18	20	29	37	M42x2	1 15	80	46130	22	95	100	263
A41Y-160	20	10	27	M33x2	105	68	46099	20	29	37	M42x2	1 15	80	46130	22	95	100	263
A41Y-160	25	12	28	M33x2	105	68	3.18	20	40	47	M52x2	165	1 15	46199	28	135	130	285
A41Y-160	32	15	37	M42x2	1 15	80	46130	22	50	59	M64x3	165	1 15	46199	32	130	135	285
A41Y-160	40	20	47	M52x2	165	1 1 5	6.26	28	65	74	M80x3	200	145	46202	40	180	165	495
A41Y-160	50	25	58	M64x3	165	1 1 5	46199	32	80	94	100x	225	170	12206	45	190	190	510
A41Y-320			27	M33x2	105	68	3.18	20	29	37	M42x2	1 15	80	4 8	22	95	100	263
A41Y-320	20	10	32	M36x2	1 10	75	46099	22	29	37	M42x2	1 15	80	46130	22	95	100	263
A41Y-320	25	1 2	35	M42x2	1 15	80	4.18	22	40	47	M52x2	165	1 15	46199	28	135	130	285
A41Y-320	32	14	41	M48x2	135	95	46134	25	50	59	M64x3	165	1 15	46199	32	130	135	285
A41Y-320	40	1 8	58	M64x3	165	1 1 5	6.26	32	65	74	M80x3	200	145	46202	40	180	165	495
A41Y-320	50	23	70	M80x3	200	145	46202	40	80	94	100x	225	170	12206	45	190	190	510

RFQ checklist

RFQ checklist: model or valve type, DN/NPS, PN/Class, set pressure, relieving medium, operating temperature, body and trim material, inlet/outlet connection standard, cap/lever/pilot options, quantity, drawing, certificate and inspection requirements.

Failure Analysis, Manufacturing Evidence and Quality Control

Common misapplication risks: incorrect thread or connection standard, insufficient certified relieving capacity, unsuitable body or trim material, operating pressure too close to set pressure, unreviewed back pressure, and installation loads transferred to the valve.

Material review: body materials: WCB carbon steel, ZG15Cr1Mo alloy steel, ZG15Cr1Mo1V/ZG20Cr1Mo1V high-temperature alloy steel, CF8/304, CF8M/316 or CF3M/316L according to model body code and service. Trim and internals: 20Cr13, 304, 316, 316L or alloy trim according to body code and medium; corrosive or high-temperature service can use stainless or alloy internals. Spring and stem: 50CrVA spring for standard service; stainless or coated fluoroplastic/304 spring options for corrosive service where specified.

Testing and inspection: Set pressure calibration, shell strength test, seat tightness/leakage test, reseating/blowdown check, dimensional inspection and material verification can be supplied according to the confirmed standard and order requirements.

Source and scope: product data is based on Zobai Safety Valve Product Catalog.pdf, catalog page 26. Project compliance remains subject to the approved datasheet, drawing, calculation and controlled certificates for the ordered configuration.

Review material traceability, type-test scope and project certificate requirements.

ZBA46 Series Pilot Operated Safety Valves

Pilot operated safety valves for higher-pressure service requiring tighter sealing and stable set pressure performance.

ZBWA42 Series Bellows Balanced Safety Valves

Bellows balanced safety valves for back pressure applications where stable performance is important.

ZBA68 Series High Temperature Steam Safety Valves

High temperature steam safety valves for boilers, steam lines, and other elevated-temperature systems.

SVL488 Series Sanitary Safety Valves

Sanitary safety valves for hygienic process lines and cleaning systems requiring cleanable pressure protection.